This section includes Government security products including GSA approved combination locks, lock parts, GSA container parts, accessories, and service tools.
For additional drill bits and other items used in the neutralization of GSA containers, please see the category, Cutting Tools and Drill Bits.
-
SPARE SCREWS KIT FOR THE MINI RIG
Paragon Tools
$5.00If the template attaching screws to your Mini Rig are getting worn, here is a replacement set to get you going again. The set comes with 2 of each of three different length screws and a hex wrench. Order a couple of sets. It’s nice to have spares...MB19-B$5.00 -
Change Key for S&G 2740B
Sargent & Greenleaf
$32.68Change key for the S&G 2740 High Security Electromechanical lock. Works with the original model 2740A and the current model 2740B. Downloads: S&G Model 2740B Operation Instructions S&G Model 2740A Operating...SG2740-105$32.68 -
STRONGARM CARBIDE END MILL - 1/4" X 6"
StrongArm Security
$44.00Solid Carbide Mill-Drills The perfect solution for drilling X-O locks! X-O locks require perfectly placed holes in the lock case when drilling for lost combinations. Even trickier, the drill must not damage critical components located inside that...SA-EM4$44.00 -
Strongarm Template T4 - Kaba Mas Electronic Locks
StrongArm Security
$78.09Accessory for the SA03 Mini-Rig. This template has precise drill locations for the Auditcon, B52, Cencon, and X-07, X-08, and X-09 locks. Resources: StrongArm Mini Rig Template GuideSA-T4$78.09 -
1/4" SAFE SAVER PIN
$9.691/4" Safe Saver carbide centered mild steel safe repair pin. Use to repair 1/4" hole through the hardplate. Requires drilling 5/16" hole through door to allow tapered repair pin to seat into hardplate.LKMSSP2250$9.69 -
STRONGARM HOLLOBORE BOLT 5/16"
StrongArm Security
$17.44Replacement Hollobore bolt for the StrongArm Mini Rig. The Hollobore bolts are used to attach the Mini Rig base to the template when setting up the rig. The 5/16" Hollobore has an internal diameter to accommodate a 5/16" diameter carbide tipped drill...SA03-HB5$17.44 -
EXTRA LONG CARBIDE END MILL 1/4" X 6"
MBA USA, Inc.
$49.47Four flute, center cutting extra long end mill 1/4" x 6". Solid carbide and made in the USA! These extra-long, corner radiused, four flute, solid carbide end mills feature a 30 helix angle and are center cutting for plunging, slotting and...LEM250-6$49.47 -
LONG CARBIDE END MILL 1/4" x 4"
MBA USA, Inc.
$37.81Four flute, center cutting extra long end mill 1/4" x 4". Solid carbide and made in the USA! These extra-long, corner radiused, four flute, solid carbide end mills feature a 30 helix angle and are center cutting for plunging, slotting and...LEM250-4$37.81 -
GSA TYPE KEY CHANGE SET
Keedex Tools
$115.16GSA Container Kit! Contains 12 of the most common combination changing keys and tools for mechanical safe locks commonly found on GSA Security Containers. LaGard; Mosler; and S&G are all well represented. Convenient and easy to keep close at hand...K-GSA$115.16 -
X-09 / X-10 SAFE LOCK CHANGE KEY AND QUICK REFERENCE
MBA USA, Inc.
$22.37This set includes a change key for Mas-Hamilton and Kaba-Mas “X-0” series locks and a reference card with instructions for the X-09 and X-10 locks. The genuine Kaba-Mas change key works on the X-07, X-08, X-09, and X-10 locks that are used on...MB53$22.37 -
5/16" x 8" MP3 Carbide Drill Bit
Lockmasters, Inc.
$12.86MP3 Carbide Drill Bit 5/16" x 8"LKM5/16X8C$12.86 -
Quick Coupler for The Mini Rig
Paragon Tools
$38.95Instead of attaching your drill directly to the shaft of your Mini Rig, this Quick Coupler fits in your drill chuck and slides over the Mini Rig's shaft for quick attachment and release. Now you won't have to support your drill and rig together when...MB19-C$38.95 -
STRONGARM TEMPLATE T1 - S&G, Diebold, LaGard, Ilco Mechanical Locks
StrongArm Security
$78.09Provides drill points for the fence, lever screw, relocker and mounting screw on S&G/Diebold/LaGard/Ilco combination locks. Resources: StrongArm Mini Rig Template GuideSA-T1$78.09 -
GSA Gray Spray Paint (12oz) - Ground Ship Only
$21.50These 12oz spray paints are mixed to match GSA factory colors. Note: Since each factory mixes its own colors, some variation may occur. Choose from: Black (#CA01) Gray (#CA02) Parchment (#CA03) Variety Pack - All 3 Colors...CA02$21.50 -
STRONGARM HOLLOBORE BOLT 1/4"
StrongArm Security
$17.44Replacement Hollobore bolt for the StrongArm Mini Rig. The Hollobore bolts are used to attach the Mini Rig base to the template when setting up the rig. The 1/4" Hollobore has an internal diameter to accommodate a 1/4" diameter carbide tipped drill bit...SA03-HB4$17.44 -
4 OZ PLASTIC MALLET
MBA USA, Inc.
$19.99MBA’s Plastic Mallet is an excellent tool for any technician or craftsperson to add to their tool bag! At just 4 ounces and less than 10 inches in length, the mallet is excellent for personal and professional projects of all kinds. The mallets...MB43$19.99 -
NOGA - 2-PIECE HAND DEBURRING TOOL SET W/ PLASTIC HANDLE AND S10 BLADE
NOGA
$7.70Noga Deburring tool with heavy duty swivel blade. For fast and easy removal of burrs from straight or curved edges and holes. This tool also comes in very handy for deburring the tubes when installing Kaba-Mas X-10 locks.NDT$7.70 -
GSA RECERTIFICATION PAPERWORK ONLY
MBA USA, Inc.
$2.00GSA Recertification paperwork. Includes one recertification inspection form and one summary form. GSA recertification labels and paperwork may only be purchased from MBA USA by Inspectors who have graduated from our GSA Approved...RLP03$2.00 -
STRONGARM MINI-RIG SCREW SET
StrongArm Security
$14.13Replacement set of screws for the Strong Arm Mini Rig. Includes different three lengths of template attaching screws and screws needed for attaching the rig base at locations other than where the hollow bore bolt is used. Also includes three...SA03-ScrewSet$14.13 -
1/4" x 6" MP3 Carbide Drill Bit
Lockmasters, Inc.
$10.72MP3 Carbide Drill Bit 1/4" x 6" Designed to work on very hard material, great for GSA red label containers The tip has a negative rake unlike other carbide bitsLKM1/4X6C$10.72